Single acting thin hydraulic jack pancake hydraulic jack

The carrying capacity of the hydraulic cylinder for synchronous lifting pushing should be greater than 1.2 times the gravity of the weight; the minimum height of the hydraulic jack is suitable. For the convenience of taking out, the minimum height of the hydraulic cylinder for synchronous lifting and pushing should be adapted to the clearance at the bottom of the weight. When the bolster supports heavy objects during the landing, the lifting height of the hydraulic jack is greater than the sum of the ties and the occipital deformation.

The carrying capacity of the Single acting high tonnage lock nut hydraulic cylinder should be greater than 1.2 times the gravity of the weight; the minimum height of the hydraulic jack is suitable. For the convenience of taking out, the minimum height of the hydraulic jack should be adapted to the clearance at the bottom of the weight. When the bolster supports heavy objects during the landing, the lifting height of the Single acting high tonnage lock nut hydraulic cylinder is greater than the sum of the ties and the occipital deformation.

China double acting hydraulic lift piston hydraulic cylinder used in construction, shipbuilding, metallurgy, mining, petrochemical, railway engineering and other industries, such as jacking, stretching, pressing and other operations. In recent years, China double acting hydraulic lift piston hydraulic cylinder has been widely used in foundation settlement tests and static piles.

Single-acting hydraulic jack and electric pump must be on a sturdy surface so that it can withstand the load, the load must be placed in the center, covering all pistons, and can only load stationary objects. If the hydraulic oil pump is damaged, deformed, or in need of repair, do not use it! When the single acting hydraulic jack reciprocating action must be extended without hindrance, to ensure complete phase contact, only when all the piston is fully retracted in order to pump the fuel.

Our Lead equipment entered the hydraulic tool industry earlier, specializing in scientific research and development, production and operation of 300 ton cheap double acting high tonnage hydraulic cylinder jack, electric pump for 30 years. Products are widely used in road, railway, bridge, city interchange, hydropower station dam, rock and soil anchorage, high-rise buildings, slope reinforcement, tunnel and, our 300 ton cheap double acting high tonnage hydraulic cylinder jack have been exported to the USA, Canada, India, Malaysia, Pakistan, Korea, Bahrain, Nepal, Azerbaijan, Mexico and so on.

High quality 1000 ton double acting 700bar hydraulic cylinder, hydraulic piston return; piston rod plating 40Cr metal layer Increase surface brightness and hardness Prevent air corrosion; the piston and the guide ring are made of copper, which is more wear resistant. High quality 1000 ton double acting 700bar hydraulic cylinder special guide ring design can withstand an eccentric load of up to 5% of the rated load capacity of the jack.

Our Lead equipment entered the hydraulic tool industry earlier, specializing in scientific research and development, production and operation of hydraulic jack, electric pump for 30 years. 500 ton double acting high tonnage hollow hydraulic jack is widely used in road, railway, bridge, city interchange, hydropower station dam, rock and soil anchorage, high-rise buildings, slope reinforcement, tunnel and, our 500 ton double acting high tonnage hollow hydraulic jack have been exported to the USA, Canada, India, Malaysia, Pakistan, Korea, Bahrain, Nepal, Azerbaijan, Mexico and so on.

Best price double acting large hydraulic cylinder jack is suitable for high-tonnage lifting operations, and requires high precision control of object lifting and maintenance operations. In the tunnel pipe horizontal displacement installation, Best price double acting large hydraulic cylinder jack hydraulic reset design can quickly and effectively retract the piston to its original position, ready to advance the next pipe.

400 ton high tonnage single acting hydraulic pressure jack high quality description: The 400 ton high tonnage single acting hydraulic pressure jack high quality with pump has a large stroke and a strong lifting capacity, and is the best choice for maintenance, manufacturing, construction and other operations. All models can be processed according to customer requirements, and the bottom is designed with mounting holes, which makes the installation and positioning convenient.

When the double acting high tonnage hydraulic piston cylinder is lifnting, it is necessary to select a hydraulic jack suitable for tonnage:
The carrying capacity of the double-acting high tonnage hydraulic piston cylinder should be greater than 1.2 times the gravity of the weight; the minimum height of the hydraulic jack is suitable. For the convenience of taking out, the minimum height of the double-acting high tonnage hydraulic piston cylinder should be adapted to the clearance at the bottom of the weight. When the bolster supports heavy objects during the landing, the lifting height of the hydraulic jack is greater than the sum of the ties and the occipital deformation.

Our post tension mono jack for railway jacking system should be equipped a YBZ2-2-50A electric power pack. YBZ series of power pack is a kind of plunger electric high pressure power pack, its rated pressure is 50Mpa, the power is 3kw. Its main function is supply power for hydraulic jack, button heading machine, hydraulic extruder, embossing machine and other hydraulic device.

The double acting hollow plunger hydraulic jack for lifting can be equipped with a two-way manual oil pump or a two-way electric oil pump. Because of the through hole in the middle, the hollow jack not only has the lifting capacity of a general hydraulic jack, but also has the stretching and tensioning functions that the ordinary jack does not have. The through hole allows cables, steel ropes and other shafts to pass through. The hollow roof has double functions and hydraulic retraction. The double acting hollow plunger hydraulic jack for lifting is the first choice for various large-scale projects. It has the characteristics of convenient operation and control. The new technology and structure make the hollow roof jacks safer and last longer.

Factory price hydraulic tensioning prestressed jack is our YDC6500 post tension hollow hydraulic jack, it is customized our customer from US. Tonnage is 650 tons, stroke is 200mm, closed height is 410mm, outer diameter is 557mm. Factory price hydraulic tensioning prestressed jack is more convenient, light and new design jack. It has compact structure, perfect seal performance, light weight, small dimension and many other features. The factory price hydraulic tensioning prestressed jack is used for stressing 27 pc strands, and it need to equip a 60Mpa 4L/min electric oil pump.

High quality double acting small hydraulic cylinder used in construction, shipbuilding, metallurgy, mining, petrochemical, railway engineering and other industries, such as jacking, stretching, pressing and other operations. In recent years, high quality double acting small hydraulic cylinder has been widely used in foundation settlement tests and static piles.

The prestressing concrete jack prestressed equipment manufacture in China is mainly used for the overall pulling force of the group anchor. The jack is easy to operate, reliable and saves steel strands than other types of jacks. Prestressing concrete jack prestressed equipment is mainly used for bridge construction and other projects that use products such as anchor bolts and tensile equipment.

The application of 300ton double acting steel hydraulic piston cylinder Made In China:
1. If the oil quantity of the pump body is insufficient, it is necessary to first add working oil (10# oil) to the pump to work.
2, estimated weight, should not be overloaded.
3. Determine the center of gravity of the lifting object and select the point of gravity of the jack. At the same time, it must take into account whether the softness and hardness of the ground are padded with tough wood to avoid the risk of dumping when lifting.
4. After the jack lifts the heavy object, the heavy material should be supported in time with the tough wood. It is forbidden to use the jack as a support. It is forbidden to use several jacks at the same time to avoid the imbalance of load and the danger of dumping.
5. When using, first connect the quick joint of the manual pump to the top, then select the position and screw the oil drain screw on the oil pump to work. Loosen the oil drain screw and unload the cylinder.
6. Please refer to the instruction manual for the electric pump.

High tonnage double acting pull hydraulic cylinder produced by Lead Equipment have undergone strict quality control before leaving the factory, so they can display their good performance when they reach the unit. Even so, we still have to spend a section to explain its post-maintenance. Because the high tonnage double acting pull hydraulic cylinder for concrete frame are placed for a long time, the internal parts will produce some minor changes. These changes are what we usually need to pay attention to. Don’t wait until you use it to remember it.

Hydraulic cylinder and electric hydraulic pump for mono strand stress jack must be on a sturdy surface so that it can withstand the load, the load must be placed in the center, covering all pistons, can only load stationary object. If the electric hydraulic pump for mono strand stress jack is damaged, deformed, or in need of repair, do not use! When the hydraulic jack cylinder reciprocating action must be extended without hindrance, to ensure complete phase contact, only when all the piston is fully retracted in order to pump the fuel.

Leadcrete brand 300ton self-lock 75mm stroke hydraulic lifting jack and electric oil pump for sale. The tonnage of this hydraulic jack is 00ton self-lock 75mm. Because our double-acting hydraulic jack own have the follow advantages, it is accepted by many different customers. 300ton self-lock 75mm stroke hydraulic lifting jack is suitable for high-tonnage lifting operations and requires high precision control of object lifting and maintenance operations. In the tunnel pipe horizontal displacement installation, its hydraulic reset design can quickly and effectively retract the piston to its original position, ready to advance the next pipe.

Lead Equipment Co., Ltd is a professional manufacturer of hydraulic cylinder for pulling with power pack in China. We could make kinds of standard and non-standard hydraulic cylinders for pulling with the oil pump.

First, 350ton spring return single acting hydraulic cylinder description: The single acting hydraulic jack with pump has a large stroke and a strong lifting capacity, and is the best choice for maintenance, manufacturing, construction and other operations. All models can be processed according to customer requirements, and the bottom is designed with mounting holes, which makes the installation and positioning convenient.
Second, the characteristics 350ton spring return single acting hydraulic cylinder with pump: The piston part is welded with copper, the piston rod is coated with hard chrome, never pulls the cylinder, and the wear resistance is strong. High temperature baking varnish, surface abrasion resistance, corrosion resistance and impact. Single-acting design, spring retraction (reset). High strength alloy steel is durable.

First, 500 ton single acting hydraulic ram jack description: The single acting hydraulic jack with pump has a large stroke and a strong lifting capacity, and is the best choice for maintenance, manufacturing, construction and other operations. All models can be processed according to customer requirements, and the bottom is designed with mounting holes, which makes the installation and positioning convenient.
Second, the characteristics 500 ton single acting hydraulic ram jack: The piston part is welded with copper, the piston rod is coated with hard chrome, never pulls the cylinder, and the wear resistance is strong. High temperature baking varnish, surface abrasion resistance, corrosion resistance and impact. Single-acting design, spring retraction (reset). High strength alloy steel is durable.

The characteristics 200-ton single-acting steel hollow plunger 700 Bar hydraulic jack: The piston part is welded with copper, the piston rod is coated with hard chrome, never pulls the cylinder, and the wear resistance is strong. High-temperature baking varnish, surface abrasion resistance, corrosion resistance and impact. Single-acting design, spring retraction (reset). High-strength alloy steel is durable.

Double acting hydraulic cylinder/jack/ram is a power tool. To avoid the possibility of a major injury, read all instructions carefully before using a double-acting hydraulic cylinder/jack/ram, warnings and precautions, and comply with the safety measures to avoid damage to persons or equipment occurring when the operation of the device!

Leadcrete Company produces double-acting steel press hydraulic cylinders with great prices for pile foundation testing. It has the characteristics of large output force, light weight and long-distance operation. Double acting steel press hydraulic cylinder with great price is equipped with a high-pressure electric oil pump station of the factory, which can realize various forms of operation such as top, push, pull and squeeze. Used in construction, shipbuilding, metallurgy, mining, petrochemical, railway engineering and other industries, such as jacking, stretching, pressing and other operations. In recent years, it has been widely used in foundation settlement tests and static piles.

Our Lead equipment entered the hydraulic tool industry earlier, specializing in scientific research and development, production and operation of double acting hydraulic jack price, electric pump for 30 years. Double acting hydraulic jack is widely used in road, railway, bridge, city interchange, hydropower station dam, rock and soil anchorage, high-rise buildings, slope reinforcement, tunnel and, double acting hydraulic jack price have been exported to the USA, Canada, India, Malaysia, Pakistan, Korea, Bahrain, Nepal, Azerbaijan, Mexico and so on.

Lead Company produces large tonnage 500 ton double acting hydraulic jack for pile foundation testing.Large tonnage 500 ton double acting hydraulic jack has the characteristics of large output force, light weight and long-distance operation. Large tonnage 500 ton double acting hydraulic jack is equipped with high-pressure electric oil pump station of the factory, which can realize various forms of operation such as top, push, pull and squeeze.

Leadcrete Company produces 250 ton single acting lock nut hydraulic jacks for sale for pile foundation testing. It has the characteristics of large output force, light weight and long-distance operation. It is equipped with high-pressure electric oil pump station of the factory, which can realize various forms of operation such as top, push, pull and squeeze. Used in construction, shipbuilding, metallurgy, mining, petrochemical, railway engineering and other industries, such as jacking, stretching, pressing and other operations. In recent years, 250 ton single acting lock nut hydraulic jacks for sale has been widely used in foundation settlement tests and static piles.

High capacity 45mm stroke single acting pancake lock nut hydraulic jack can be used for the maintenance of large machinery, the overall lifting of the bridge, the maintenance of the hydropower plant gate, the lifting of the steel structure and the installation of supporting equipment. If you want to know more high capacity 45mm stroke single acting pancake lock nut hydraulic jack information, please contact us!

Lead equipment specializes in the production of hot sell single acting high tonnage lock nut hydraulic jack, providing you with 50 ton, 100ton, 200ton, 300ton, 500ton, 600ton, 800ton, 1000ton and 1500 tons of hot sell single acting high tonnage lock nut hydraulic jack, we have many types for you choose, we can also customize according to your requirements.